Digilent 410-221P Bedienungsanleitung PDF herunterladen

™

Revision: October 11, 2011

1300 NE Henley Court, Suite 3

Pullman, WA 99163

(509) 334 6306 Voice | (509) 334 6300 Fax

Doc: 502-221 page 1 of 2

Overview

The PmodTMP2 is a temperature sensor and

thermostat control board built around the

Analog Devices ADT7420.

Features include:

• Up to 16-bit resolution

• Typical accuracy better than 0.25 °C

• I

C interface with 4 selectable

addresses

• 240ms continuous conversion time

• Support for 3.3v and 5v interfaces

• No calibration required

• Programmable

overtemperature/undertemperature

control pins.

Functional Description

The PmodTMP2 uses an 8-pin connector that

allows for communication via I

C, and provides

pins to daisy-chain the PmodTMP2 to other I

devices. The PmodTMP2 also provides two 2-

pin headers for selecting the I

C address of the

chip, and two 2-pin headers for controlling

external devices based upon temperature

thresholds defined by the user in software.

C Interface

The PmodTMP2’s onboard ADT7420 chip acts

as a slave device using the industry standard

C communication scheme. To communicate

with the PmodTMP2 device the I

C master

device must specify a slave address (0x48-

0x4B) and a flag indicating whether the

communication is a read (1) or a write (0). This

is followed by the actual data transfer. For the

ADT7420, the data transfer should consist of

the address of the desired device register

followed by the data to be written to the

specified register. To read from a register the

master must write the desired register address

to ADT7420, then send an I

C restart

condition, and send a new read request to the

ADT7420. If the master does not generate a

restart condition prior to attempting the read,

then the value written to the address register

will be reset to 0x00.

As some registers stored 16-bit values as 8-bit

increment the address register of the device

when accessing certain registers such as the

temperature registers and the threshold

registers. This allows for the master to use a

single read or write request to access both the

low and high bytes of these registers. A

complete listing of registers and their behavior

can be found in the ADT7420 datasheet

available on the Analog Devices web site.

The I

C interface standard uses two signal

lines. These are I

C data and I

C clock. These

signals map to the serial data (SDA) and serial

clock (SCL) respectively on the ADT7420.

Connector J1

–

I2C Communications

Signal

Description

1, 2 SCL I2C Clock

3, 4 SDA I2C Data

5, 6 GND Power Supply Ground

7, 8 VCC Power Supply (3.3V/5V)

Interface Connector Signal Description

1 2

Inhaltsverzeichnis

Seite 1 - Functional Description

PPmmooddTTMMPP22™™ RReeffeerreennccee MMaannuuaall Revision: October 11, 2011 1300 NE Henley Court, Suite 3 Pullman, WA 99163 (509) 334 6306 Voice

Seite 2 - Quickstart Operation

Kommentare zu diesen Handbüchern

Keine Kommentare

Digilent 410-221P Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Digilent 410-221P herunter. Digilent 410-221P User Manual [cs] [pl] [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Digilent 410-221P