Digilent 410-155P-KIT Bedienungsanleitung PDF herunterladen

Revision: November 11, 2010

1300 Henley Court | Pullman, WA 99163

(509) 334 6306 Voice and Fax

Introduction

The Basys2 board is a circuit design and

implementation platform that anyone can use

to gain experience building real digital circuits.

Built around a Xilinx Spartan-3E Field

Programmable Gate Array and a Atmel

AT90USB2 USB controller, the Basys2 board

provides complete, ready-to-use hardware

suitable for hosting circuits ranging from basic

logic devices to complex controllers. A large

collection of on-board I/O devices and all

required FPGA support circuits are included,

so countless designs can be created without

the need for any other components.

Four standard expansion connectors allow

designs to grow beyond the Basys2 board

using breadboards, user-designed circuit

boards, or Pmods (Pmods are inexpensive

analog and digital I/O modules that offer A/D

& D/A conversion, motor drivers, sensor

inputs, and many other features). Signals on

the 6-pin connectors are protected against

ESD damage and short-circuits, ensuring a

long operating life in any environment. The

Basys2 board works seamlessly with all

versions of the Xilinx ISE tools, including the free WebPack. It ships with a USB cable that provides

power and a programming interface, so no other power supplies or programming cables are required.

The Basys2 board can draw power and be programmed via its on-board USB2 port. Digilent’s freely

available PC-based Adept software automatically detects the Basys2 board, provides a programming

interface for the FPGA and Platform Flash ROM, and allows user data transfers (see

www.digilentinc.com

for more information).

The Basys2 board is designed to work with the free ISE WebPack CAD software from Xilinx.

WebPack can be used to define circuits using schematics or HDLs, to simulate and synthesize

circuits, and to create programming files. Webpack can be downloaded free of charge from

www.xilinx.com/ise/

The Basys2 board ships with a built-in self-test/demo stored in its ROM that can be used to test all

board features. To run the test, set the Mode Jumper (see below) to ROM and apply board power. If

the test is erased from the ROM, it can be downloaded and reinstalled at any time. See

www.digilentinc.com/Basys2

for the test project as well as further documentation, reference designs,

and tutorials.

Xilinx Spartan3E-100 CP132

VGA Port

Platform

Flash

(config ROM)

Settable Clock

Source

(25 / 50 / 100 MHz)

Full Speed

USB2 Port

(JTAG and data transfers)

JA JB JC JD

JTAG

port

O Devices

PS/2

Port

Pmod Connectors

8 bit

color

Data

port

• 100,000-gate Xilinx Spartan 3E FPGA

• Atmel AT90USB2 Full-speed USB2 port providing board power

and programming/data transfer interface

• Xilinx Platform Flash ROM to store FPGA configurations

• 8 LEDs, 4-digit 7-segment display, 4 buttons, 8 slide switches

• PS/2 port and 8-bit VGA port

• User-settable clock (25/50/100MHz), plus socket for 2

clock

• Four 6-pin header expansion connectors

• ESD and short-circuit protection on all I/O signals.

Figure 1. Basys2 board block diagram and features

Doc: 502-155 page 1 of 12

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - Xilinx Spartan3E-100 CP132

DDiiggiilleenntt BBaassyyss22 BBooaarrdd RReeffeerreennccee MMaannuuaall Revision: November 11, 2010 1300 Henley Court | Pullman, WA 99163 (50

Seite 2 - Doc: 502-138 page 2 of 12

Basys2 Reference Manual Digilent www.digilentinc.com A VGA controller circuit must generate the HS and VS timings signals and coordinate the delive

Seite 3 - Doc: 502-138 page 3 of 12

Basys2 Reference Manual Digilent www.digilentinc.com Expansion Connectors (6-pin headers) The Basys2 board provides four 6-pin peripheral module co

Seite 4 - Doc: 502-138 page 4 of 12

Basys2 Reference Manual Digilent www.digilentinc.com Built in Self Test The Basys2 board comes preloaded with a simple self test/demonstration proj

Seite 5 - Doc: 502-138 page 5 of 12

Basys2 Reference Manual Digilent www.digilentinc.com Board Power The Basys2 board is typically powered from a USB cable, but a battery connector is

Seite 6 - Doc: 502-138 page 6 of 12

Basys2 Reference Manual Digilent www.digilentinc.com To program the Basys2 board, set the mode jumper to PC and attach the USB cable to the board.

Seite 7 - Figure 12. Mouse data format

Basys2 Reference Manual Digilent www.digilentinc.com User I/O Four pushbuttons and eight slide switches are provided for circuit inputs. Pushbutton

Seite 8 - Doc: 502-138 page 8 of 12

Basys2 Reference Manual Digilent www.digilentinc.com For each of the four digits to appear bright and continuously illuminated, all four digits shou

Seite 9 - Display Surface

Basys2 Reference Manual Digilent www.digilentinc.com Keyboard The keyboard uses open-collector drivers so the keyboard or an attached host device

Seite 10 - Digilent

Basys2 Reference Manual Digilent www.digilentinc.com The keyboard sends data to the host in 11-bit words that contain a ‘0’ start bit, followed by 8

Seite 11

Basys2 Reference Manual Digilent www.digilentinc.com VGA Port The Basys2 board uses 10 FPGA signals to create a VGA port with 8-bit color and the t

Seite 12 - Basys2 Reference Manual

Basys2 Reference Manual Digilent www.digilentinc.com entire phosphor-coated display surface of the CRT being charged to 20kV (or more). The rays are

Kommentare zu diesen Handbüchern

Keine Kommentare

Digilent 410-155P-KIT Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Digilent 410-155P-KIT herunter. Digilent 410-155P-KIT User Manual [en] [de] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Digilent 410-155P-KIT